|Opcode/Instruction||Op/En||64/32 bit Mode Support||CPUID Feature Flag||Description|
|0F DF /r1 PANDN mm, mm/m64||RM||V/V||MMX||Bitwise AND NOT of mm/m64 and mm.|
|66 0F DF /r PANDN xmm1, xmm2/m128||RM||V/V||SSE2||Bitwise AND NOT of xmm2/m128 and xmm1.|
|VEX.NDS.128.66.0F.WIG DF /r VPANDN xmm1, xmm2, xmm3/m128||RVM||V/V||AVX||Bitwise AND NOT of xmm3/m128 and xmm2.|
|VEX.NDS.256.66.0F.WIG DF /r VPANDN ymm1, ymm2, ymm3/m256||RVM||V/V||AVX2||Bitwise AND NOT of ymm2, and ymm3/m256 and store result in ymm1.|
Notes: 1. See note in Section 2.4, “Instruction Exception Specification” in the Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 2A and Section 22.25.3, “Exception Conditions of Legacy SIMD Instructions Operating on MMX Registers” in the Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 3A.
|Op/En||Operand 1||Operand 2||Operand 3||Operand 4|
|RM||ModRM:reg (r, w)||ModRM:r/m (r)||NA||NA|
|RVM||ModRM:reg (w)||VEX.vvvv (r)||ModRM:r/m (r)||NA|
Performs a bitwise logical NOT operation on the first source operand, then performs bitwise AND with second source operand and stores the result in the destination operand. Each bit of the result is set to 1 if the corresponding bit in the first operand is 0 and the corresponding bit in the second operand is 1, otherwise it is set to 0.
In 64-bit mode, using a REX prefix in the form of REX.R permits this instruction to access additional registers (XMM8-XMM15).
Legacy SSE instructions: The source operand can be an MMX technology register or a 64-bit memory location. The destination operand can be an MMX technology register. 128-bit Legacy SSE version: The first source operand is an XMM register. The second operand can be an XMM register or a 128-bit memory location. The destination is not distinct from the first source XMM register and the upper bits (VLMAX-1:128) of the corresponding YMM register destination are unmodified. VEX.128 encoded version: The first source operand is an XMM register. The second source operand is an XMM register or 128-bit memory location. The destination operand is an XMM register. The upper bits (VLMAX-1:128) of the corresponding YMM register destination are zeroed. VEX.256 encoded version: The first source operand is a YMM register. The second source operand is a YMM register or a 256-bit memory location. The destination operand is a YMM register.
Note: VEX.L must be 0, otherwise the instruction will #UD.
PANDN(128-bit Legacy SSE version) DEST ← NOT(DEST) AND SRC DEST[VLMAX-1:128] (Unmodified) VPANDN (VEX.128 encoded version) DEST ← NOT(SRC1) AND SRC2 DEST[VLMAX-1:128] ← 0 VPANDN (VEX.256 encoded instruction) DEST[255:0] ← ((NOT SRC1[255:0]) AND SRC2[255:0])
|PANDN:||__m64 _mm_andnot_si64 (__m64 m1, __m64 m2)|
|(V)PANDN:||__m128i _mm_andnot_si128 ( __m128i a, __m128i b)|
|VPANDN:||__m256i _mm256_andnot_si256 ( __m256i a, __m256i b)|
See Exceptions Type 4; additionally
|#UD||If VEX.L = 1.|